View 74HC4053PW_1168962.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the 74hc4053; 74hct4053 is a high-speed si-gate cmos device and is pin compatible with the hef4053b. it is speci?ed in compliance with jedec standard no. 7a. the 74hc4053; 74hct4053 is triple 2-channel analog multiplexer/demultiplexer with a common enable input ( e). each multiplexer/demultiplexer has two independent inputs/outputs (ny0 and ny1), a common input/output (nz) and three digital select inputs (sn). with e low, one of the two switches is selected (low-impedance on-state) by s1 to s3. with e high, all switches are in the high-impedance off-state, independent of s1 to s3. v cc and gnd are the supply voltage pins for the digital control inputs (s1 to s3 and e). the v cc to gnd ranges are 2.0 v to 10.0 v for 74hc4053 and 4.5 v to 5.5 v for 74hct4053. the analog inputs/outputs (ny0 and ny1, and nz) can swing between v cc as a positive limit and v ee as a negative limit. v cc - v ee may not exceed 10.0 v. for operation as a digital multiplexer/demultiplexer, v ee is connected to gnd (typically ground). 2. features n low on resistance: u 80 w (typical) at v cc - v ee = 4.5 v u 70 w (typical) at v cc - v ee = 6.0 v u 60 w (typical) at v cc - v ee = 9.0 v n logic level translation: u to enable 5 v logic to communicate with 5 v analog signals n typical break before make built in n complies with jedec standard no. 7a n esd protection: u hbm eia/jesd22-a114-c exceeds 2000 v u mm eia/jesd22-a115-a exceeds 200 v n multiple package options n speci?ed from - 40 cto+85 c and from - 40 c to +125 c 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer rev. 04 9 may 2006 product data sheet
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 2 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 3. applications n analog multiplexing and demultiplexing n digital multiplexing and demultiplexing n signal gating 4. quick reference data [1] c pd is used to determine the dynamic power dissipation (p d in m w). p d =c pd v cc 2 f i + ? {(c l + c s ) v cc 2 f o } where: f i = input frequency in mhz; f o = output frequency in mhz; ? {(c l + c s ) v cc 2 f o } = sum of outputs; table 1: quick reference data v ee = gnd = 0 v; t amb =25 c; t r =t f = 6 ns. symbol parameter conditions min typ max unit 74hc4053 t pzh , t pzl turn-on time c l = 15 pf; r l =1k w ; v cc =5 v e to v os -17-ns sn to v os -21-ns t phz , t plz turn-off time c l = 15 pf; r l =1k w ; v cc =5 v e to v os -18-ns sn to v os -17-ns c i input capacitance - 3.5 - pf c s switch capacitance independent i/o (nyn) - 5 - pf common i/o (nz) - 8 - pf c pd power dissipation capacitance per switch; v i = gnd to v cc [1] -36-pf 74hct4053 t pzh , t pzl turn-on time c l = 15 pf; r l =1k w ; v cc =5 v e to v os -23-ns sn to v os -21-ns t phz , t plz turn-off time c l = 15 pf; r l =1k w ; v cc =5 v e to v os -20-ns sn to v os -19-ns c i input capacitance - 3.5 - pf c s switch capacitance independent i/o (nyn) - 5 - pf common i/o(nz) - 8 - pf c pd power dissipation capacitance per switch; v i = gnd to (v cc - 1.5 v) [1] -36-pf
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 3 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer c l = output load capacitance in pf; c s = maximum switch capacitance in pf; v cc = supply voltage in v. 5. ordering information table 2: ordering information type number package temperature range name description version 74hc4053 74hc4053n - 40 c to +125 c dip16 plastic dual in-line package; 16 leads (300 mil); long body sot38-4 74hc4053d - 40 c to +125 c so16 plastic small outline package; 16 leads; body width 3.9 mm sot109-1 74hc4053db - 40 c to +125 c ssop16 plastic shrink small outline package; 16 leads; body width 5.3 mm sot338-1 74HC4053PW - 40 c to +125 c tssop16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm sot403-1 74hc4053bq - 40 c to +125 c dhvqfn16 plastic dual in-line compatible thermal enhanced very thin quad ?at package; no leads; 16 terminals; body 2.5 3.5 0.85 mm sot763-1 74hct4053 74hct4053n - 40 c to +125 c dip16 plastic dual in-line package; 16 leads (300 mil); long body sot38-4 74hct4053d - 40 c to +125 c so16 plastic small outline package; 16 leads; body width 3.9 mm sot109-1 74hct4053db - 40 c to +125 c ssop16 plastic shrink small outline package; 16 leads; body width 5.3 mm sot338-1 74hct4053pw - 40 c to +125 c tssop16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm sot403-1 74hct4053bq - 40 c to +125 c dhvqfn16 plastic dual in-line compatible thermal enhanced very thin quad ?at package; no leads; 16 terminals; body 2.5 3.5 0.85 mm sot763-1
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 4 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 6. functional diagram fig 1. functional diagram fig 2. logic symbol fig 3. iec logic symbol 001aae124 logic level conversion 11 16 v cc 13 1y1 s1 decoder 12 1y0 14 1z 1 2y1 2 2y0 15 2z 3 3y1 5 3y0 43z 10 s2 9 87 gnd v ee s3 6 e 001aae125 1y0 12 1y1 s1 13 11 s2 10 s3 9 6 e 2y0 2 2y1 1 3y0 5 3y1 3 3z 4 2z 15 1z 14 001aae126 6 en 11 # # # mux/dmux 12 13 0 1 0/1 0 1 14 10 2 1 15 9 5 3 4
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 5 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 7. pinning information 7.1 pinning fig 4. schematic diagram (one switch) 001aad544 from logic v cc v ee v ee v cc v cc v ee y z v cc (1) the die substrate is attached to this pad using conductive die attach material. it can not be used as supply pin or input. fig 5. pin con?guration dip16, so16 and (t)ssop16 fig 6. pin con?guration dhvqfn16 74hc4053 74hct4053 2y1 v cc 2y0 2z 3y1 1z 3z 1y1 3y0 1y0 es1 v ee s2 gnd s3 001aae127 1 2 3 4 5 6 7 8 10 9 12 11 14 13 16 15 001aae128 v ee s2 es1 3y0 1y0 3z 1y1 3y1 1z 2y0 2z gnd s3 2y1 v cc transparent top view 7 10 6 11 5 12 4 13 3 14 2 15 8 9 1 16 terminal 1 index area gnd (1) 74hc4053 74hct4053
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 6 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 7.2 pin description 8. functional description 8.1 function table [1] h = high voltage level; l = low voltage level; x = dont care. 9. limiting values table 3: pin description symbol pin description 2y1 1 2 independent input/output 1 2y0 2 2 independent input/output 0 3y1 3 3 independent input/output 1 3z 4 3 common input/output 3y0 5 3 independent input/output 0 e 6 enable input (active low) v ee 7 negative supply voltage gnd 8 ground (0 v) s3 9 select input 3 s2 10 select input 2 s1 11 select input 1 1y0 12 1 independent input/output 0 1y1 13 1 independent input/output 1 1z 14 1 common input/output 2z 15 2 common input/output v cc 16 supply voltage table 4: function table [1] control channel on e sn l l ny0 to nz h ny1 to nz h x none table 5: limiting values in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to v ee = gnd (ground = 0 v). [1] symbol parameter conditions min max unit v cc supply voltage - 0.5 +11.0 v i ik input clamping current v i < - 0.5 v or v i >v cc + 0.5 v - 20 ma i sk switch clamping current v s < - 0.5 v or v s >v cc + 0.5 v - 20 ma
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 7 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer [1] to avoid drawing v cc current out of terminals nz, when switch current ?ows in terminals nyn, the voltage drop across the bidirectional switch must not exceed 0.4 v. if the switch current ?ows into terminals nz, no v cc current will ?ow out of terminals nyn. in this case there is no limit for the voltage drop across the switch, but the voltages at nyn and nz may not exceed v cc or v ee . [2] for dip16 package: p tot derates linearly with 12 mw/k above 70 c. [3] for so16 package: p tot derates linearly with 8 mw/k above 70 c. [4] for ssop16 and tssop16 packages: p tot derates linearly with 5.5 mw/k above 60 c. [5] for dhvqfn16 packages: p tot derates linearly with 4.5 mw/k above 60 c. 10. recommended operating conditions i s switch current - 0.5 v < v s 74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 8 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 11. static characteristics v i input voltage gnd - v cc v v s switch voltage v ee -v cc v t amb ambient temperature - 40 +25 +125 c t r , t f input rise and fall times v cc = 4.5 v - 6.0 500 ns table 6: recommended operating conditions continued symbol parameter conditions min typ max unit a. type 74hc4053 b. type 74hct4053 fig 7. guaranteed operating area as a function of the supply voltages v cc - v ee (v) 010 8 46 2 001aad545 4 6 2 8 10 0 operating area v cc - gnd (v) v cc - v ee (v) 010 8 46 2 001aad546 4 6 2 8 10 0 v cc - gnd (v) operating area table 7: r on resistance per switch 74hc4053 and 74hct4053 for test circuit see figure 8 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. 74hc4053 supply voltages: v cc - gnd or v cc - v ee = 2.0 v, 4.5 v, 6.0 v and 9.0 v. 74hct4053 supply voltages: v cc - gnd = 4.5 v or 5.5 v; v cc - v ee = 2.0 v, 4.5 v, 6.0 v and 9.0 v. symbol parameter conditions min typ max unit t amb = 25 c r on(peak) on resistance (peak) v is = v cc to v ee ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v; i s = 100 m a [1] --- w v cc = 4.5 v; v ee = 0 v; i s = 1000 m a - 100 180 w v cc = 6.0 v; v ee = 0 v; i s = 1000 m a - 90 160 w v cc = 4.5 v; v ee = - 4.5 v; i s = 1000 m a - 70 130 w
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 9 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer r on(rail) on resistance (rail) v is = v ee ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v; i s = 100 m a [1] - 150 - w v cc = 4.5 v; v ee = 0 v; i s = 1000 m a - 80 140 w v cc = 6.0 v; v ee = 0 v; i s = 1000 m a - 70 120 w v cc = 4.5 v; v ee = - 4.5 v; i s = 1000 m a - 60 105 w v is = v cc ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v; i s = 100 m a [1] - 150 - w v cc = 4.5 v; v ee = 0 v; i s = 1000 m a - 90 160 w v cc = 6.0 v; v ee = 0 v; i s = 1000 m a - 80 140 w v cc = 4.5 v; v ee = - 4.5 v; i s = 1000 m a - 65 120 w d r on on resistance mismatch between channels v is = v cc to v ee ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v [1] --- w v cc = 4.5 v; v ee = 0 v - 9 - w v cc = 6.0 v; v ee = 0 v - 8 - w v cc = 4.5 v; v ee = - 4.5 v - 6 - w t amb = - 40 c to +85 c r on(peak) on resistance (peak) v is = v cc to v ee ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v; i s = 100 m a [1] --- w v cc = 4.5 v; v ee = 0 v; i s = 1000 m a - - 225 w v cc = 6.0 v; v ee = 0 v; i s = 1000 m a - - 200 w v cc = 4.5 v; v ee = - 4.5 v; i s = 1000 m a - - 165 w r on(rail) on resistance (rail) v is = v ee ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v; i s = 100 m a [1] --- w v cc = 4.5 v; v ee = 0 v; i s = 1000 m a - - 175 w v cc = 6.0 v; v ee = 0 v; i s = 1000 m a - - 150 w v cc = 4.5 v; v ee = - 4.5 v; i s = 1000 m a - - 130 w v is = v cc ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v; i s = 100 m a [1] --- w v cc = 4.5 v; v ee = 0 v; i s = 1000 m a - - 200 w v cc = 6.0 v; v ee = 0 v; i s = 1000 m a - - 175 w v cc = 4.5 v; v ee = - 4.5 v; i s = 1000 m a - - 150 w t amb = - 40 c to +125 c r on(peak) on resistance (peak) v is = v cc to v ee ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v; i s = 100 m a [1] --- w v cc = 4.5 v; v ee = 0 v; i s = 1000 m a - - 270 w v cc = 6.0 v; v ee = 0 v; i s = 1000 m a - - 240 w v cc = 4.5 v; v ee = - 4.5 v; i s = 1000 m a - - 195 w table 7: r on resistance per switch 74hc4053 and 74hct4053 continued for test circuit see figure 8 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. 74hc4053 supply voltages: v cc - gnd or v cc - v ee = 2.0 v, 4.5 v, 6.0 v and 9.0 v. 74hct4053 supply voltages: v cc - gnd = 4.5 v or 5.5 v; v cc - v ee = 2.0 v, 4.5 v, 6.0 v and 9.0 v. symbol parameter conditions min typ max unit
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 10 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer [1] at supply voltages (v cc - v ee ) approaching 2.0 v the analog switch on resistance becomes extremely non-linear. therefore, it is recommended that these devices be used to transmit digital signals only, when using these supply voltages. r on(rail) on resistance (rail) v is = v ee ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v; i s = 100 m a [1] --- w v cc = 4.5 v; v ee = 0 v; i s = 1000 m a - - 210 w v cc = 6.0 v; v ee = 0 v; i s = 1000 m a - - 180 w v cc = 4.5 v; v ee = - 4.5 v; i s = 1000 m a - - 160 w v is = v cc ; v i = v ih or v il v cc = 2.0 v; v ee = 0 v; i s = 100 m a [1] --- w v cc = 4.5 v; v ee = 0 v; i s = 1000 m a - - 240 w v cc = 6.0 v; v ee = 0 v; i s = 1000 m a - - 210 w v cc = 4.5 v; v ee = - 4.5 v; i s = 1000 m a - - 180 w table 7: r on resistance per switch 74hc4053 and 74hct4053 continued for test circuit see figure 8 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. 74hc4053 supply voltages: v cc - gnd or v cc - v ee = 2.0 v, 4.5 v, 6.0 v and 9.0 v. 74hct4053 supply voltages: v cc - gnd = 4.5 v or 5.5 v; v cc - v ee = 2.0 v, 4.5 v, 6.0 v and 9.0 v. symbol parameter conditions min typ max unit r on =v s / i s .v is =0vto(v cc - v ee ). (1) v cc = 4.5 v (2) v cc =6v (3) v cc =9v fig 8. test circuit for measuring r on fig 9. typical r on as a function of input voltage v is 001aae129 v s nyn nz i s v is = 0 v to (v cc - v ee ) high (from select input) v ee v is (v) 0 9.0 7.2 3.6 5.4 1.8 mnb047 50 70 30 90 110 10 r on ( w ) (1) (2) (3)
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 11 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer table 8: static characteristics 74hc4053 at recommended operating conditions; voltages are referenced to gnd (ground = 0 v). v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit t amb = 25 c v ih high-state input voltage v cc = 2.0 v 1.5 1.2 - v v cc = 4.5 v 3.15 2.4 - v v cc = 6.0 v 4.2 3.2 - v v cc = 9.0 v 6.3 4.7 - v v il low-state input voltage v cc = 2.0 v - 0.8 0.5 v v cc = 4.5 v - 2.1 1.35 v v cc = 6.0 v - 2.8 1.8 v v cc = 9.0 v - 4.3 2.7 v i li input leakage current v i = v cc or gnd; v ee = 0 v v cc = 6.0 v - - 0.1 m a v cc = 10.0 v - - 0.2 m a i s(off) off-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 10 per channel - - 0.1 m a all channels - - 0.1 m a i s(on) on-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 11 -- 0.1 m a i cc quiescent supply current v is = v ee or v cc ; v os = v cc or v ee ; v i =v cc or gnd; v ee = 0 v v cc = 6.0 v - - 8.0 m a v cc = 10.0 v - - 16.0 m a c i input capacitance - 3.5 - pf c s switch capacitance independent i/o (nyn) - 5 - pf common i/o (nz) - 8 - pf t amb = - 40 c to +85 c v ih high-state input voltage v cc = 2.0 v 1.5 - - v v cc = 4.5 v 3.15 - - v v cc = 6.0 v 4.2 - - v v cc = 9.0 v 6.3 - - v v il low-state input voltage v cc = 2.0 v - - 0.5 v v cc = 4.5 v - - 1.35 v v cc = 6.0 v - - 1.8 v v cc = 9.0 v - - 2.7 v i li input leakage current v i = v cc or gnd; v ee = 0 v v cc = 6.0 v - - 1.0 m a v cc = 10.0 v - - 2.0 m a
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 12 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer i s(off) off-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 10 per channel - - 1.0 m a all channels - - 1.0 m a i s(on) on-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 11 -- 1.0 m a i cc quiescent supply current v is = v ee or v cc ; v os = v cc or v ee ; v i =v cc or gnd; v ee = 0 v v cc = 6.0 v - - 80.0 m a v cc = 10.0 v - - 160.0 m a t amb = - 40 c to +125 c v ih high-state input voltage v cc = 2.0 v 1.5 - - v v cc = 4.5 v 3.15 - - v v cc = 6.0 v 4.2 - - v v cc = 9.0 v 6.3 - - v v il low-state input voltage v cc = 2.0 v - - 0.5 v v cc = 4.5 v - - 1.35 v v cc = 6.0 v - - 1.8 v v cc = 9.0 v - - 2.7 v i li input leakage current v i = v cc or gnd; v ee = 0 v v cc = 6.0 v - - 1.0 m a v cc = 10.0 v - - 2.0 m a i s(off) off-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 10 per channel - - 1.0 m a all channels - - 1.0 m a i s(on) on-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 11 -- 1.0 m a i cc quiescent supply current v is = v ee or v cc ; v os = v cc or v ee ; v i =v cc or gnd; v ee = 0 v v cc = 6.0 v - - 160.0 m a v cc = 10.0 v - - 320.0 m a table 8: static characteristics 74hc4053 continued at recommended operating conditions; voltages are referenced to gnd (ground = 0 v). v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit table 9: static characteristics 74hct4053 voltages are referenced to gnd (groun d=0v). v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit t amb = 25 c v ih high-state input voltage v cc = 4.5 v to 5.5 v 2.0 1.6 - m a v il low-state input voltage v cc = 4.5 v to 5.5 v - 1.2 0.8 m a
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 13 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer i li input leakage current v cc = 5.5 v; v ee = 0 v; v i = v cc or gnd - - 0.1 m a i s(off) off-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 10 per channel - - 0.1 m a all channels - - 0.1 m a i s(on) on-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 11 -- 0.1 m a i cc quiescent supply current v i = v cc or gnd; v is = v ee or v cc ; v os =v cc or v ee v cc = 5.5 v; v ee = 0 v - - 8.0 m a v cc = 5.0 v; v ee = - 5.0 v - - 16.0 m a d i cc additional quiescent supply current per input pin; v cc = 4.5 v to 5.5 v; v ee = 0 v; v i = v cc - 2.1 v; other inputs at v cc or gnd - 50 180 m a c i input capacitance - 3.5 - pf c s switch capacitance independent i/o (nyn) - 5 - pf common i/o (nz) - 8 - pf t amb = - 40 c to +85 c v ih high-state input voltage v cc = 4.5 v to 5.5 v 2.0 - - m a v il low-state input voltage v cc = 4.5 v to 5.5 v - - 0.8 m a i li input leakage current v cc = 5.5 v; v ee = 0 v; v i = v cc or gnd - - 1.0 m a i s(off) off-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 10 per channel - - 1.0 m a all channels - - 1.0 m a i s(on) on-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 11 -- 1.0 m a i cc quiescent supply current v i = v cc or gnd; v is = v ee or v cc ; v os =v cc or v ee v cc = 5.5 v; v ee = 0 v - - 80.0 m a v cc = 5.0 v; v ee = - 5.0 v - - 160.0 m a d i cc additional quiescent supply current per input pin; v cc = 4.5 v to 5.5 v; v ee = 0 v; v i = v cc - 2.1 v; other inputs at v cc or gnd - - 225 m a t amb = - 40 c to +125 c v ih high-state input voltage v cc = 4.5 v to 5.5 v 2.0 - - m a v il low-state input voltage v cc = 4.5 v to 5.5 v - - 0.8 m a i li input leakage current v cc = 5.5 v; v ee = 0 v; v i = v cc or gnd - - 1.0 m a table 9: static characteristics 74hct4053 continued voltages are referenced to gnd (groun d=0v). v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 14 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 12. dynamic characteristics i s(off) off-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 10 per channel - - 1.0 m a all channels - - 1.0 m a i s(on) on-state leakage current v cc = 10.0 v; v i = v ih or v il ; v ee =0v; | v s | = v cc - v ee ; see figure 11 -- 1.0 m a i cc quiescent supply current v i = v cc or gnd; v is = v ee or v cc ; v os =v cc or v ee v cc = 5.5 v; v ee = 0 v - - 160.0 m a v cc = 5.0 v; v ee = - 5.0 v - - 320.0 m a d i cc additional quiescent supply current per input pin; v cc = 4.5 v to 5.5 v; v ee = 0 v; v i = v cc - 2.1 v; other inputs at v cc or gnd - - 245 m a table 9: static characteristics 74hct4053 continued voltages are referenced to gnd (groun d=0v). v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit fig 10. test circuit for measuring off-state leakage current fig 11. test circuit for measuring on-state leakage current 001aae130 aa nyn sn nz v i = v cc or v ee v o = v ee or v cc low (select input) v ee 001aae131 a v i = v ee or v cc v o (open circuit) high (select input) v ee nyn sn nz table 10: dynamic characteristics type 74hc4053 voltages are referenced to gnd (ground = 0 v); t r =t f = 6 ns; c l = 50 pf unless otherwise speci?ed; for test circuit see figure 14 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit t amb = 25 c t phl , t plh propagation delay v is to v os r l = w ; see figure 12 v cc = 2.0 v; v ee = 0v - 1560ns v cc = 4.5 v; v ee = 0 v - 5 12 ns v cc = 6.0 v; v ee = 0 v - 4 10 ns v cc = 4.5 v; v ee = - 4.5 v - 4 8 ns
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 15 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer t pzh , t pzl turn-on time r l = 1 k w ; see figure 13 e to v os v cc = 2.0 v; v ee = 0 v - 60 220 ns v cc = 4.5 v; v ee = 0v - 2044ns v cc = 6.0 v; v ee = 0v - 1637ns v cc = 4.5 v; v ee = - 4.5 v - 15 31 ns v cc = 5 v; v ee =0v; c l =15pf - 17 - ns sn to v os v cc = 2.0 v; v ee = 0 v - 75 220 ns v cc = 4.5 v; v ee = 0v - 2544ns v cc = 6.0 v; v ee = 0v - 2037ns v cc = 4.5 v; v ee = - 4.5 v - 15 31 ns v cc = 5 v; v ee =0v; c l =15pf - 21 - ns t phz , t plz turn-off time r l = 1 k w ; see figure 13 e to v os v cc = 2.0 v; v ee = 0 v - 63 210 ns v cc = 4.5 v; v ee = 0v - 2142ns v cc = 6.0 v; v ee = 0v - 1736ns v cc = 4.5 v; v ee = - 4.5 v - 15 29 ns v cc = 5 v; c l =15pf - 18 - ns sn to v os v cc = 2.0 v; v ee = 0 v - 60 210 ns v cc = 4.5 v; v ee = 0v - 2042ns v cc = 6.0 v; v ee = 0v - 1636ns v cc = 4.5 v; v ee = - 4.5 v - 15 29 ns v cc = 5 v; c l =15pf - 17 - ns c pd power dissipation capacitance per switch; v i = gnd to v cc [1] -36-pf t amb = - 40 c to +85 c t phl , t plh propagation delay v is to v os r l = w ; see figure 12 v cc = 2.0 v; v ee = 0 v - - 75 ns v cc = 4.5 v; v ee = 0 v - - 15 ns v cc = 6.0 v; v ee = 0 v - - 13 ns v cc = 4.5 v; v ee = - 4.5 v - - 10 ns table 10: dynamic characteristics type 74hc4053 continued voltages are referenced to gnd (ground = 0 v); t r =t f = 6 ns; c l = 50 pf unless otherwise speci?ed; for test circuit see figure 14 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 16 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer t pzh , t pzl turn-on time r l = 1 k w ; see figure 13 e to v os v cc = 2.0 v; v ee = 0 v - - 275 ns v cc = 4.5 v; v ee = 0 v - - 55 ns v cc = 6.0 v; v ee = 0 v - - 47 ns v cc = 4.5 v; v ee = - 4.5 v - - 39 ns sn to v os v cc = 2.0 v; v ee = 0 v - - 275 ns v cc = 4.5 v; v ee = 0 v - - 55 ns v cc = 6.0 v; v ee = 0 v - - 47 ns v cc = 4.5 v; v ee = - 4.5 v - - 39 ns t phz , t plz turn-off time r l = 1 k w ; see figure 13 e to v os v cc = 2.0 v; v ee = 0 v - - 265 ns v cc = 4.5 v; v ee = 0 v - - 53 ns v cc = 6.0 v; v ee = 0 v - - 45 ns v cc = 4.5 v; v ee = - 4.5 v - - 36 ns sn to v os v cc = 2.0 v; v ee = 0 v - - 265 ns v cc = 4.5 v; v ee = 0 v - - 53 ns v cc = 6.0 v; v ee = 0 v - - 45 ns v cc = 4.5 v; v ee = - 4.5 v - - 36 ns t amb = - 40 c to +125 c t phl , t plh propagation delay v is to v os r l = w ; see figure 12 v cc = 2.0 v; v ee = 0 v - - 90 ns v cc = 4.5 v; v ee = 0 v - - 18 ns v cc = 6.0 v; v ee = 0 v - - 15 ns v cc = 4.5 v; v ee = - 4.5 v - - 12 ns t pzh , t pzl turn-on time r l = 1 k w ; see figure 13 e to v os v cc = 2.0 v; v ee = 0 v - - 330 ns v cc = 4.5 v; v ee = 0 v - - 66 ns v cc = 6.0 v; v ee = 0 v - - 56 ns v cc = 4.5 v; v ee = - 4.5 v - - 47 ns sn to v os v cc = 2.0 v; v ee = 0 v - - 330 ns v cc = 4.5 v; v ee = 0 v - - 66 ns v cc = 6.0 v; v ee = 0 v - - 56 ns v cc = 4.5 v; v ee = - 4.5 v - - 47 ns table 10: dynamic characteristics type 74hc4053 continued voltages are referenced to gnd (ground = 0 v); t r =t f = 6 ns; c l = 50 pf unless otherwise speci?ed; for test circuit see figure 14 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 17 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer [1] c pd is used to determine the dynamic power dissipation (p d in m w): p d =c pd v cc 2 f i + ? {(c l + c s ) v cc 2 f o } where: f i = input frequency in mhz; f o = output frequency in mhz; ? {(c l + c s ) v cc 2 f o } = sum of outputs; c l = output load capacitance in pf; c s = maximum switch capacitance in pf; v cc = supply voltage in v. t phz , t plz turn-off time r l = 1 k w ; see figure 13 e to v os v cc = 2.0 v; v ee = 0 v - - 315 ns v cc = 4.5 v; v ee = 0 v - - 63 ns v cc = 6.0 v; v ee = 0 v - - 54 ns v cc = 4.5 v; v ee = - 4.5 v - - 44 ns sn to v os v cc = 2.0 v; v ee = 0 v - - 315 ns v cc = 4.5 v; v ee = 0 v - - 63 ns v cc = 6.0 v; v ee = 0 v - - 54 ns v cc = 4.5 v; v ee = - 4.5 v - - 44 ns table 10: dynamic characteristics type 74hc4053 continued voltages are referenced to gnd (ground = 0 v); t r =t f = 6 ns; c l = 50 pf unless otherwise speci?ed; for test circuit see figure 14 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit table 11: dynamic characteristics type 74hct4053 voltages are referenced to gnd (groun d = 0 v); t r =t f = 6 ns; c l = 50 pf unless otherwise speci?ed; for test circuit see figure 14 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit t amb = 25 c t phl , t plh propagation delay v is to v os v cc = 4.5 v; r l = w ; see figure 12 v ee = 0 v - 5 12 ns v ee = - 4.5 v - 4 8 ns t pzh , t pzl turn-on time r l = 1 k w ; see figure 13 e to v os v cc = 4.5 v; v ee = 0v - 2748ns v cc = 4.5 v; v ee = - 4.5 v - 16 34 ns v cc = 5 v; v ee =0v; c l =15pf - 23 - ns sn to v os v cc = 4.5 v; v ee = 0v - 2548ns v cc = 4.5 v; v ee = - 4.5 v - 16 34 ns v cc = 5 v; v ee =0v; c l =15pf - 21 - ns
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 18 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer t phz , t plz turn-off time r l = 1 k w ; see figure 13 e to v os v cc = 4.5 v; v ee = 0v - 2444ns v cc = 4.5 v; v ee = - 4.5 v - 15 31 ns v cc = 5 v; v ee =0v; c l =15pf - 20 - ns sn to v os v cc = 4.5 v; v ee = 0v - 2244ns v cc = 4.5 v; v ee = - 4.5 v - 15 31 ns v cc = 5 v; v ee =0v; c l =15pf - 19 - ns c pd power dissipation capacitance per switch; v i = gnd to (v cc - 1.5 v) [1] -36-pf t amb = - 40 c to +85 c t phl , t plh propagation delay v is to v os v cc = 4.5 v; r l = w ; see figure 12 v ee = 0 v - - 15 ns v ee = - 4.5 v - - 10 ns t pzh , t pzl turn-on time v cc = 4.5 v; r l =1k w ; see figure 13 e to v os v ee = 0 v - - 60 ns v ee = - 4.5 v - - 43 ns sn to v os v ee = 0 v - - 60 ns v ee = - 4.5 v - - 43 ns t phz , t plz turn-off time v cc = 4.5 v; r l =1k w ; see figure 13 e to v os v ee = 0 v - - 55 ns v ee = - 4.5 v - - 39 ns sn to v os v ee = 0 v - - 55 ns v ee = - 4.5 v - - 39 ns t amb = - 40 c to +125 c t phl , t plh propagation delay v is to v os v cc = 4.5 v; r l = w ; see figure 12 v ee = 0 v - - 18 ns v ee = - 4.5 v - - 12 ns t pzh , t pzl turn-on time v cc = 4.5 v; r l =1k w ; see figure 13 e to v os v ee = 0 v - - 72 ns v ee = - 4.5 v - - 51 ns sn to v os v ee = 0 v - - 72 ns v ee = - 4.5 v - - 51 ns table 11: dynamic characteristics type 74hct4053 continued voltages are referenced to gnd (groun d = 0 v); t r =t f = 6 ns; c l = 50 pf unless otherwise speci?ed; for test circuit see figure 14 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 19 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer [1] c pd is used to determine the dynamic power dissipation (p d in m w): p d =c pd v cc 2 f i + ? {(c l + c s ) v cc 2 f o } where: f i = input frequency in mhz; f o = output frequency in mhz; ? {(c l + c s ) v cc 2 f o } = sum of outputs; c l = output load capacitance in pf; c s = maximum switch capacitance in pf; v cc = supply voltage in v. 13. waveforms t phz , t plz turn-off time v cc = 4.5 v; r l =1k w ; see figure 13 e to v os v ee = 0 v - - 66 ns v ee = - 4.5 v - - 47 ns sn to v os v ee = 0 v - - 66 ns v ee = - 4.5 v - - 47 ns table 11: dynamic characteristics type 74hct4053 continued voltages are referenced to gnd (groun d = 0 v); t r =t f = 6 ns; c l = 50 pf unless otherwise speci?ed; for test circuit see figure 14 . v is is the input voltage at a nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at a nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit fig 12. propagation delay input (v is ) to output (v os ) 001aad555 t plh t phl 50 % 50 % v is input v os output
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 20 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer (1) measurement points are given in t ab le 12 . fig 13. turn-on and turn-off times table 12: measurement points type input v m 74hc4053 0.5v cc 74hct4053 1.3 v 001aae330 t plz t phz switch off switch on switch on v os output v os output e, sn inputs v m v i 0 v 90 % 10 % t pzl t pzh 50 % 50 %
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 21 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer [1] v i values: a) for 74hc4053: v i =v cc . b) for 74hct4053: v i =3v . test data is given in t ab le 13 . r t = termination resistance should be equal to output impedance z o of the pulse generator. c l = load capacitance including jig and probe capacitance. r l = load resistor. s1 = test selection switch. fig 14. load circuitry for switching times table 13: test data test input load s1 position v i v is t r , t f c l r l at f max other t phl , t plh [1] pulse < 2 ns 6 ns 15 pf, 50 pf 1 k w open t pzh , t phz [1] v cc < 2 ns 6 ns 15 pf, 50 pf 1 k w v ee t pzl , t plz [1] v ee < 2 ns 6 ns 15 pf, 50 pf 1 k w v cc v m v m t w t w 10 % 90 % 0 v v i v i negative pulse positive pulse 0 v v m v m 90 % 10 % t f t r t r t f 001aae382 v cc v cc open gnd v ee v i v os dut c l r t r l s1 pulse generator v is
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 22 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 14. additional dynamic characteristics [1] adjust input voltage v is to 0 dbm level (0 dbm = 1 mw into 600 w ). [2] control input e or sn, with square-wave between v cc and gnd. [3] adjust input voltage v is to 0 dbm level at v os for 1 mhz (0 dbm = 1 mw into 50 w ). table 14: additional dynamic characteristics 74hc4053 and 74hct4053 gnd = 0 v; t amb =25 c. v is is the input voltage at an nyn or nz terminal, whichever is assigned as an input. v os is the output voltage at an nyn or nz terminal, whichever is assigned as an output. symbol parameter conditions min typ max unit d sin sine wave distortion r l = 10 k w ; c l = 50 pf; see figure 15 f i = 1 khz v cc = 2.25 v; v ee = - 2.25 v; v is = 4.0 v (p-p) - 0.04 - % v cc = 4.5 v; v ee = - 4.5 v; v is = 8.0 v (p-p) - 0.02 - % f i =10khz v cc = 2.25 v; v ee = - 2.25 v; v is = 4.0 v (p-p) - 0.12 - % v cc = 4.5 v; v ee = - 4.5 v; v is = 8.0 v (p-p) - 0.06 - % a (off)(ft) off-state feed-through attenuation r l = 600 w ; c l = 50 pf; f i = 1 mhz; see figure 16 [1] v cc = 2.25 v; v ee = - 2.25 v - - 50 - db v cc = 4.5 v; v ee = - 4.5 v - - 50 - db v ct(sw-sw) crosstalk between switches r l = 600 w ; c l = 50 pf; f i = 1 mhz; see figure 17 [1] v cc = 2.25 v; v ee = - 2.25 v - - 60 - db v cc = 4.5 v; v ee = - 4.5 v - - 60 - db v ct(d-sw) crosstalk between digital inputs and switch v cc = 4.5 v; r l = 600 k w ; c l = 50 pf; f i = 1 mhz; see figure 18 [2] v ee = 0 v - 110 - mv v ee = - 4.5 v - 220 - mv f (-3db) - 3 db frequency response r l =50 w ; c l = 10 pf; see figure 19 [3] v cc = 2.25 v; v ee = - 2.25 v - 160 - mhz v cc = 4.5 v; v ee = - 4.5 v - 170 - mhz fig 15. test circuit for measuring sine wave distortion 001aae132 10 m f r l v os v is c l db nyn or nz nz or nyn gnd channel on
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 23 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer a. feed-through as function of the frequency b. test circuit fig 16. typical switch off signal feed-through as a function of frequency 001aae332 f i (khz) 10 10 5 10 6 10 4 10 2 10 3 - 60 - 40 - 80 - 20 0 a (off)(ft) (db) - 100 001aae133 0.1 m f r l v os v is c l db gnd channel off nyn or nz nz or nyn
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 24 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer a. switch on b. switch off fig 17. test circuits for measuring crosstalk between any two switches fig 18. test circuit for measuring crosstalk between digital inputs and switch 001aae134 0.1 m f r l r l v os v is c l db nyn or nz nz or nyn gnd channel on 001aae259 r l v os v is c l db gnd channel off r l nyn or nz nz or nyn dut 001aae135 2r l 2r l 2r l 2r l nz or nyn nyn or nz c l oscilloscope v cc v cc gnd v ee v ct(d-sw) sn or e
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 25 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer a. typical frequency response b. test circuit fig 19. typical frequency response 001aad551 f (khz) 10 10 5 10 6 10 4 10 2 10 3 - 1 1 - 3 3 5 v os (db) - 5 001aae132 10 m f r l v os v is c l db nyn or nz nz or nyn gnd channel on
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 26 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 15. package outline fig 20. package outline sot38-4 (dip16) references outline version european projection issue date iec jedec jeita sot38-4 95-01-14 03-02-13 m h c (e ) 1 m e a l seating plane a 1 w m b 1 b 2 e d a 2 z 16 1 9 8 e pin 1 index b 0 5 10 mm scale note 1. plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. unit a max. 12 b 1 (1) (1) (1) b 2 cd e e m z h l mm dimensions (inch dimensions are derived from the original mm dimensions) a min. a max. b max. w m e e 1 1.73 1.30 0.53 0.38 0.36 0.23 19.50 18.55 6.48 6.20 3.60 3.05 0.254 2.54 7.62 8.25 7.80 10.0 8.3 0.76 4.2 0.51 3.2 inches 0.068 0.051 0.021 0.015 0.014 0.009 1.25 0.85 0.049 0.033 0.77 0.73 0.26 0.24 0.14 0.12 0.01 0.1 0.3 0.32 0.31 0.39 0.33 0.03 0.17 0.02 0.13 dip16: plastic dual in-line package; 16 leads (300 mil) sot38-4
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 27 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer fig 21. package outline sot109-1 (so16) x w m q a a 1 a 2 b p d h e l p q detail x e z e c l v m a (a ) 3 a 8 9 1 16 y pin 1 index unit a max. a 1 a 2 a 3 b p cd (1) e (1) (1) eh e ll p qz y w v q references outline version european projection issue date iec jedec jeita mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 0 o o 0.25 0.1 dimensions (inch dimensions are derived from the original mm dimensions) note 1. plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 sot109-1 99-12-27 03-02-19 076e07 ms-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.041 0.244 0.228 0.028 0.020 0.028 0.012 0.01 0.25 0.01 0.004 0.039 0.016 0 2.5 5 mm scale so16: plastic small outline package; 16 leads; body width 3.9 mm sot109-1
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 28 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer fig 22. package outline sot338-1 (ssop16) unit a 1 a 2 a 3 b p cd (1) e (1) eh e ll p qz y w v q references outline version european projection issue date iec jedec jeita mm 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 6.4 6.0 5.4 5.2 0.65 1.25 7.9 7.6 1.03 0.63 0.9 0.7 1.00 0.55 8 0 o o 0.13 0.2 0.1 dimensions (mm are the original dimensions) note 1. plastic or metal protrusions of 0.25 mm maximum per side are not included. sot338-1 99-12-27 03-02-19 (1) w m b p d h e e z e c v m a x a y 1 8 16 9 q a a 1 a 2 l p q detail x l (a ) 3 mo-150 pin 1 index 0 2.5 5 mm scale ssop16: plastic shrink small outline package; 16 leads; body width 5.3 mm sot338-1 a max. 2
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 29 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer fig 23. package outline sot403-1 (tssop16) unit a 1 a 2 a 3 b p cd (1) e (2) (1) eh e ll p qz y w v q references outline version european projection issue date iec jedec jeita mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 8 0 o o 0.13 0.1 0.2 1 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 sot403-1 mo-153 99-12-27 03-02-18 w m b p d z e 0.25 18 16 9 q a a 1 a 2 l p q detail x l (a ) 3 h e e c v m a x a y 0 2.5 5 mm scale tssop16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm sot403-1 a max. 1.1 pin 1 index
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 30 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer fig 24. package outline sot763-1 (dhvqfn16) terminal 1 index area 0.5 1 a 1 e h b unit y e 0.2 c references outline version european projection issue date iec jedec jeita mm 3.6 3.4 d h 2.15 1.85 y 1 2.6 2.4 1.15 0.85 e 1 2.5 0.30 0.18 0.05 0.00 0.05 0.1 dimensions (mm are the original dimensions) sot763-1 mo-241 - - - - - - 0.5 0.3 l 0.1 v 0.05 w 0 2.5 5 mm scale sot763-1 dhvqfn16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm a (1) max. a a 1 c detail x y y 1 c e l e h d h e e 1 b 27 15 10 9 8 1 16 x d e c b a terminal 1 index area a c c b v m w m e (1) note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. d (1) 02-10-17 03-01-27
74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 31 of 33 philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 16. abbreviations 17. revision history table 15: abbreviations acronym description cmos complementary metal oxide semiconductor hbm human body model esd electrostatic discharge mm machine model dut device under test table 16: revision history document id release date data sheet status change notice doc. number supersedes 74hc_hct4053_4 20060509 product data sheet - - 74hc_hct4053_3 modi?cations: ? section 5 order ing inf or mation : errors corrected, type numbers in wrong order and sot38-4 is the package for types 74hc4053n and 74hct4053n 74hc_hct4053_3 20060315 product data sheet - - 74hc_hct4053_ cnv_2 modi?cations: ? the format of this data sheet has been redesigned to comply with the new presentation and information standard of philips semiconductors. ? added type numbers 74hc4053bq and 74hct4053bq (dhvqfn16) package to section 5 order ing inf or mation , section 7 pinning inf or mation and section 15 p ac kage outline 74hc_hct4053_cnv_2 19901201 product speci?cation - - -
philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 74hc_hct4053_4 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 04 9 may 2006 32 of 33 18. data sheet status [1] please consult the most recently issued data sheet before initiating or completing a design. [2] the product status of the device(s) described in this data sheet may have changed since this data sheet was published. the l atest information is available on the internet at url http://www.semiconductors.philips.com. [3] for data sheets describing multiple type numbers, the highest-level product status determines the data sheet status. 19. de?nitions short-form speci?cation the data in a short-form speci?cation is extracted from a full data sheet with the same type number and title. for detailed information see the relevant data sheet or data handbook. limiting values de?nition limiting values given are in accordance with the absolute maximum rating system (iec 60134). stress above one or more of the limiting values may cause permanent damage to the device. these are stress ratings only and operation of the device at these or at any other conditions above those given in the characteristics sections of the speci?cation is not implied. exposure to limiting values for extended periods may affect device reliability. application information applications that are described herein for any of these products are for illustrative purposes only. philips semiconductors makes no representation or warranty that such applications will be suitable for the speci?ed use without further testing or modi?cation. 20. disclaimers life support these products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. philips semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify philips semiconductors for any damages resulting from such application. right to make changes philips semiconductors reserves the right to make changes in the products - including circuits, standard cells, and/or software - described or contained herein in order to improve design and/or performance. when the product is in full production (status production), relevant changes will be communicated via a customer product/process change noti?cation (cpcn). philips semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise speci?ed. 21. trademarks notice all referenced brands, product names, service names and trademarks are the property of their respective owners. 22. contact information for additional information, please visit: http://www.semiconductors.philips.com for sales of?ce addresses, send an email to: sales.addresses@www.semiconductors.philips.com level data sheet status [1] product status [2] [3] de?nition i objective data development this data sheet contains data from the objective speci?cation for product development. philips semiconductors reserves the right to change the speci?cation in any manner without notice. ii preliminary data quali?cation this data sheet contains data from the preliminary speci?cation. supplementary data will be published at a later date. philips semiconductors reserves the right to change the speci?cation without notice, in order to improve the design and supply the best possible product. iii product data production this data sheet contains data from the product speci?cation. philips semiconductors reserves the right to make changes at any time in order to improve the design, manufacturing and supply. relevant changes will be communicated via a customer product/process change noti?cation (cpcn).
? koninklijke philips electronics n.v. 2006 all rights are reserved. reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. the information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. no liability will be accepted by the publisher for any consequence of its use. publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights. date of release: 9 may 2006 document number: 74hc_hct4053_4 published in the netherlands philips semiconductors 74hc4053; 74hct4053 triple 2-channel analog multiplexer/demultiplexer 23. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 quick reference data . . . . . . . . . . . . . . . . . . . . . 2 5 ordering information . . . . . . . . . . . . . . . . . . . . . 3 6 functional diagram . . . . . . . . . . . . . . . . . . . . . . 4 7 pinning information . . . . . . . . . . . . . . . . . . . . . . 5 7.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 7.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 6 8 functional description . . . . . . . . . . . . . . . . . . . 6 8.1 function table . . . . . . . . . . . . . . . . . . . . . . . . . . 6 9 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 6 10 recommended operating conditions. . . . . . . . 7 11 static characteristics. . . . . . . . . . . . . . . . . . . . . 8 12 dynamic characteristics . . . . . . . . . . . . . . . . . 14 13 waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 14 additional dynamic characteristics . . . . . . . . 22 15 package outline . . . . . . . . . . . . . . . . . . . . . . . . 26 16 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 31 17 revision history . . . . . . . . . . . . . . . . . . . . . . . . 31 18 data sheet status . . . . . . . . . . . . . . . . . . . . . . . 32 19 de?nitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 20 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 21 trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 22 contact information . . . . . . . . . . . . . . . . . . . . 32

▲Up To Search▲

Price & Availability of 74HC4053PW

	To Download 74HC4053PW Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .